Skip to main content
Ctrl+K
Logo image

Edge.Auto Documentation

Site Navigation

  • Getting Started
  • User Manual
  • Hardware Reference Manual
  • FAQs
  • Knowledge Base
  • Downloads
  • TIER IV ADK
  • TIER IV

Site Navigation

  • Getting Started
  • User Manual
  • Hardware Reference Manual
  • FAQs
  • Knowledge Base
  • Downloads
  • TIER IV ADK
  • TIER IV

Section Navigation

  • 1. Automotive Camera
    • 1.1. Can I adjust the camera settings such as exposure, gain, and shutter speed?
    • 1.2. What are the options for C1 camera Field of View (FOV)?
    • 1.3. What are the options for C2 camera Field of View (FOV)?
    • 1.4. What is the camera size of C1 for each lens?
    • 1.5. What is the camera size of C2 for each lens?
    • 1.6. Can I change the frame rate?
    • 1.7. What is the shutter type?
    • 1.8. Does the camera have a zoom function?
    • 1.9. Can I switch the shutter mode between rolling and global?
    • 1.10. What’s the maximum length of the cable I can use?
    • 1.11. Can I use a different ECU other than the recommended one?
    • 1.12. What is the image delay from the camera to the ECU?
    • 1.13. Is it possible to communicate and supply power with PoE?
    • 1.14. Can I use the cameras with a USB interface?
    • 1.15. Is it compatible with PTP IEEE1588?
    • 1.16. How do I install the camera driver?
    • 1.17. How can I inquire about products and services?
    • 1.18. What should I do if the product is defective or malfunctions?
    • 1.19. What is the operating temperature range of the cameras?
    • 1.20. Is exterior CAD data available?
    • 1.21. What environmental standards do the cameras comply with?
    • 1.22. Can I use the C1 and C2 at the same time, with the same ECU?
    • 1.23. Can I use the Raspberry pi to receive the data from the TIER IV cameras by using GMSL2-USB3.0 converter?
    • 1.24. Can I fix the relationship between the GMSL port number and the device name?
    • 1.25. Some cameras don’t start streaming image when I connect multiple (for instance, 8) cameras. This happens occasionally
    • 1.26. I would like to know which ECU I can use with TIER IV cameras and from who I should get support.
  • 2. Sensor Fusion System
    • 2.1. Is the software for performing sensor fusion publicly available?
    • 2.2. How can I find step-by-step instructions to build the kit?
    • 2.3. Will it work even with sensor configurations different from the sample configuration?
    • 2.4. Will it work even with ECU configurations different from the sample configuration?
    • 2.5. Why do you need a camera and Lidar synchronization? How do you synchronize?
    • 2.6. What is calibration? Why do you need calibration?
    • 2.7. Does the provided software (sample application) work on Windows and Mac operating systems?
    • 2.8. If I purchase from an authorized distributor, will the sensor drivers be pre-installed?
    • 2.9. Can I purchase the board required for calibration?
    • 2.10. I would like to ask for technical support for introduction, is it possible?
  • 3. GMSL2-10GbE Conversion Module
    • 3.1. How much host performance is needed to receive the image from GMSL2-10GbE conversion module?
  • FAQs
  • 1. Automotive Camera
  • 1.11. Can I use a different ECU other than the recommended one?

1.11. Can I use a different ECU other than the recommended one?#

The cameras should work with other ECUs by modifying the camera driver.

The cameras can be used for various ECUs by using the GMSL2-USB3 conversion kit (sold separately).

previous

1.10. What’s the maximum length of the cable I can use?

next

1.12. What is the image delay from the camera to the ECU?
Last updated on 2024-10-02

© Copyright 2023, TIER IV.